offers 553 4135 alloy steel products. About 59% of these are steel pipes, 21% are steel round bars, and 4% are steel sheets. A wide variety of 4135 alloy steel options are available to you, such as aisi, din, and astm.
EN 1.0145 (S275J2) Non Alloy Steel EN 1.0145 steel is a carbon (non alloy) steel formulated for primary forming into wrought products. Cited properties are appropriate for the hot worked condition. 1.0145 is the EN numeric designation for this material. S275J2 is the EN chemical designation.
Stainless Steel, Special Steel, Compressor Blading, Turbine Blading, Superalloy Supplier. S275J2 can be supplied as steel plate/ sheet, round steel bar, steel tube/pipe, steel stripe, steel billet, steel ingot, steel wire rods. electroslag, forged ring/ block,etc.
S275J2 is a low carbon, high tensile strength structural steel which can be readily welded to other weldable steel. With its low carbon equivalent, it possesses good cold forming properties. The plate is produced by fully killed steel process and supplied in normalized or controlled rolling condition. S275J2
Tool & Die Steels Inc. Stainless Steel, Special Steel, Compressor Blading, Turbine Blading, Superalloy Supplier. SAE 4135 Round Bar SAE 4135 Flat Bar SAE 4135 Hollow Bar SAE 4135 Tube / Pipe SAE 4135 Sheet / Plate SAE 4135 Strip / Coil SAE 4135 Wire SAE 4135 Forging SAE 4135 Tube / Pipe TEL:+86 80247006
4135 (USA, AISI, ASTM, UNS ) European (EU, EN) and wordwide Steel equivalent grades These comparison table is only intended as an indication of the closest khown equivalent grades. The source standarts should always be checked for the specific purpose for each material, in case of doubt Buy, sell, suppliers search product 4135 on line
EN 10025 S275 Steel (S275JR, S275J0 & S275J2) EN 10025 S275 Steel is a non alloy structural steel grade, according to EN10025, S275 mild steel is mainly devided into S275JR (1.0044), S275J0 (1.0143) and S275J2 (1.0145). Some properties of S275 mild steel is better than S235, and lower than S355.
Under EN 10025 2,there are three different steel grade for S275,it is S275J2,S275J0 and S275JR.S275j2 steel plate need to be done low temperature impacting test under minus 20 centigree,S275J0 done under zero centigree and S275JR steel
Materials » Alloys » Steel » Alloy Steel » ASTM A517 Grade P Materials » Alloys » Steel » Alloy Steel » ASTM A517 Grade A Materials » Alloys » Steel » Stainless Steel » AISI Type 429
Alloy steels comprise a broad spectrum of steels whose compositions are more than the limitations of C, Mo, Cr, Va, Mn, Ni, Si, and B which have been fixed for carbon steels. These steels are more responsive to mechanical and heat treatments than carbon steels. The following datasheet will provide details about AISI 4137 alloy steel.
4135 Good strength, good machinability, heat treatable, good toughness 4135 is a chromium molybdenum low alloy steel. The addition of molybdenum improves the strength of the 4135. It can be heat treated to even increase the strength, and maintain its toughness at reasonable levels.
Stainless Steel, Special Steel, Compressor Blading, Turbine Blading, Superalloy Supplier. ASTM 4135 can be supplied as steel plate/ sheet, round steel bar, steel tube/pipe, steel stripe, steel billet, steel ingot, steel wire rods. electroslag, forged ring/ block,etc. Join Supplier[email protected]
Gangsteel is specialized in supplying EN10025 2 steel plate in S275J2. For more information of S275J2 steel plates, please check them in followingChemical composition % of the Product analysis of grade S275J2 (1.0145) Nominal thickness =< 30(mm) CEV max =
Carbon structural steel plate S275J2 with normal strength of 275Mpa yield strength,this steel just . contian five main chemical elements,no any alloy elements in S275J2 steel,so we call it carbon steel . plate,also called plain_carbon steel plate.As the carbon content rises,steel plate has the ability
Property Data; This page displays only the text of a material data sheet. To see MatWeb's complete data sheet for this material (including material property data, metal compositions, material suppliers, etc), please click the button below.
The graph bars on the material properties cards below compare EN 1.0143 steel towrought carbon or non alloy steels (top), all iron alloys (middle), and the entire database (bottom). A full bar means this is the highest value in the relevant set. A half full bar means it's 50% of the highest, and so on.
WARNINGAlthough we have taken the utmost care in the drafting of the website, Sidastico Spa assumes no responsibility for the accuracy and exactness of the information set forth herein and reserves the right to change any part of the same without advance notice.
· 20 Years of experience in the Steel field
· 500,000 MT production capacity per year.
· 100+ exporting markets covering global main countries and regions.
· 2000+ MT stock per month with different materials and sizes.
· 150+ projects each year, covering oil tank, shipbuilding, oil&gas pipeline, drilling, offshore, energy, construction industries.
Our Steel Products' Certificates: