Stainless Steel, Special Steel, Compressor Blading, Turbine Blading, Superalloy Supplier. P3 can be supplied as steel plate/ sheet, round steel bar, steel tube/pipe, steel stripe, steel billet, steel ingot, steel wire rods. electroslag, forged ring/ block,etc.
Low carbon Mold Steel (UNS T51603), Mold steels are used for plastic molds and lower temperature die casting. AISI Type P3 Low carbon Mold Steel (UNS T51603) CategoriesMetal; Ferrous Metal; or engineering calculations can click on the property value to see the original value as well as raw conversions to equivalent units.
Stainless Steel, Special Steel, Compressor Blading, Turbine Blading, Superalloy Supplier. AISI/SAE P1 can be supplied as steel plate/ sheet, round steel bar, steel tube/pipe, steel stripe, steel billet, steel ingot, steel wire rods. electroslag, forged ring/ block,etc.
Steel Grade Equivalent Table (EN, SAE/AISI, UNS, DIN, BS, UNI, JIS) The table below compares common grades of materials from various international specifications. Note that materials compared are the nearest available grade and may have slight variations in actual chemistry.
30CrNiMo8 ( 1.6580 ) Alloy special steels EN 10297 12003 Seamless circular steel tubes for mechanical and general engineering purposes. Non alloy and alloy steel tubes
Chemical composition and properties of european equivalents (EN) for 20 (China, GB )P235TR1 (1.0254) , P235GH (1.0345) , P355N (1.0562) , C22 (1.0402) , 20 (China, GB ) European (EU, EN) and wordwide Steel equivalent grades. These comparison table is only intended as an indication of the closest khown equivalent grades.
DIN EN 1.4404 material (stainless steel X2CrNiMo17 12 2) is a low carbon version of 1.4401, equivalent to AISI 316L, datasheet, properties, heat treatment
17HNM, 18NiCrMo5, 17CrNiMo6 4, 18CrNiMo7 6, 1.6566 specification and application. Alloy steel 17HNM is a grade consisting of the addition of chromium, nickel, molybdenum and coal with a range characteristic for all carburizing grades. 17HNM materials, unlike other simple steel grades, can be used for much larger sizes and loads.
Steel mould and Steel mould suppliers, global delivery, stock supply Steel mould steels. Heat Resistant Steel . Heat resistant steel. AS Orlov Izobret. Mashinostr. 3, 48 49, 7/2000. The purpose of this work was to increase plasticity of heat resistant steel after aging at the 500 1300 deg C temperature and to improve its operational reliability.
From Tradewell Ferromet Pvt Ltd, India, Maharashtra, Khopoli, Mumbai client can avail smaller quantities of Alloy Steel 30CrNIMo8 Bars, 30CrNiMo8 Round Bar, Construction Alloy steel 30CrNiMo8 Steel Bar, 30CrNiMo8 Flat Bar, 30CrNiMo8 Ring, 30CrNiMo8 Hollow Bar, 30CrNiMo8 Pipe, Alloy Steel Bars online by sending us an email.
Non alloy quality steel Chemical composition of steel P235GH (1.0345), Standards of steel P235GH (1.0345) Mechanical Properties of steel P235GH (1.0345) Equivalent grades of steel P235GH (1.0345) steel P235GH (1.0345) Tensile Strength, Elongation, Proof strength , Hardness
Mold steels are designated as group P steels according to the AISI classification system. These steels consist of one medium carbon steel and all low carbon P series tool steels such as P2, P3, P4, P5, P6, P20, and P21 type steels.
EN 1.6587 steel is an alloy steel formulated for primary forming into wrought products. 1.6587 is the EN numeric designation for this material. 18CrNiMo7 6 is the EN chemical designation. It has a moderately high density among EN wrought alloy steels. In addition, it has a fairly high base cost and a moderately high electrical conductivity.
30CrNiMo8, 1.6580 specification and application. Alloyed structural steel with medium hardenability designed for heavy duty components, characterized by high elasticity and strength properties reaching over 1560 N/mm 2 at small diameters. When softened, the hardness reaches max. 248 HRB.
The steel 17 CrNiMo 6 is used for high loaded parts in the vehicle and mechanical engineering with high demands on toughness and core strength (e.g. gear parts, drive pinions). The lowest application amounts to 60 °C. Equivalent standards are similar to one or more standards provided by the supplier. Some equivalent standards may be
Nov 11, 2013 · Julio, there's no AISI 4130 pipe material. As Al has perfectly explained, AISI standards (AISI is the American Institute of Steel and Iron) simply states the chemical composition of a certain steel identified by a number. In this case, the number is 4130. American standards covering pipe materials are ASTM, ASME Section II, API, AWWA.
With DuoNian production experience, strict control 1.5415, DIN 15Mo3, AISI A182 Grade F1 chemical composition and 1.5415, DIN 15Mo3, AISI A182 Grade F1 mechanical properties.From casting, forging, steel to hot and cold rolling process, heat treatment, etc, we have the control of professional engineers.
More than 85% of the steel produced and shipped in the United States is carbon steel. Low carbon steels contain up to 0.30% C. The largest category of this class of steel is flat rolled products (sheet or strip), usually in the cold rolled and annealed condition.
· 20 Years of experience in the Steel field
· 500,000 MT production capacity per year.
· 100+ exporting markets covering global main countries and regions.
· 2000+ MT stock per month with different materials and sizes.
· 150+ projects each year, covering oil tank, shipbuilding, oil&gas pipeline, drilling, offshore, energy, construction industries.
Our Steel Products' Certificates: